Liebherr delivers the first MTC 78000 heavy lift offshore crane
At the end of June, Liebherr delivered the first heavy lift offshore crane type MTC 78000 straight from its manufacturing plant in Rostock. The MTC 78000 is one of the biggest offshore slewing cranes worldwide. With a maximum dynamic torque of 78,000 mT, the MTC 78000 is the most powerful machine within the extensive range of cranes and material handling machines offered by the Liebherr group of companies. Four units of the new heavy-lift crane have already been ordered to date.
Despite its size, the MTC 78000 has been designed as a slewing crane and is supported by traditional large-diameter antifriction bearings. With a weight of 70 tons, the swing ring has a diameter of approximately 9 m. The manufacturing of such large mechanical parts can only be accomplished through complicated custom processes as conventional gear cutting machines are only available for large-diameter anti-friction bearings up to a diameter of 5 m. Therefore, Liebherr has acquired correspondingly sized machines and equipment specifically for the mechanical machining of these flanges.
Spectacular heavy lifting
The onsite erection and assembly of the large size crane on the heavy load vessel OSA Goliath presented Liebherr engineers with special challenges – for example, the planning of the individual hoists so that the maximum permitted ground pressure of the pier was not exceeded. As the assembly starting date depended on the arrival of the heavy load vessel and the required lifting equipment needed to be ready on short notice, Liebherr exclusively used their own cranes for the assembly. Two large LHM 600 mobile harbour cranes were used in tandem operation for the heavy duty lifts. Both cranes with their maximum load capacity of 208 tons each enabled parts weighing up to 400 tons to be mounted in tandem operation. The machines were equipped with the recently patented innovative Liebherr “sycratronic” control system. This Dynamic Anti Collision System controls the simultaneous operation of the mobile harbour cranes, so ensuring best possible performance and protection for the cranes.
The assembly of the MTC 78000 required several spectacular heavy duty lifts. First, the slewing platform was mounted – at 370 t, the heaviest of the components. Thereafter, the machinery compartment with the drive components (approximately 240 t), the mast lower section (about 250 t) and the mast upper section (around 160 t) of which the lowest point needed to be hoisted up to over 43 m above the pier level. This hoisting height was made possible by equipping the mobile harbour cranes with two corresponding tower extensions.
The last step in the assembly process involved putting the boom in place. In a tandem hoist operation, the 87 m boom was positioned with millimeter precision at the respective connection points enabling the boom to be pinned to the slewing platform on both sides. The sheer size of the pins required a specially developed hydraulic pinning machine.
Due to precise project planning, the specially trained team of 50 mechanics was able to assemble the MTC 78000 in only 23 days.
Overload test offshore
The heavy lifting test of the large crane was carried out in the open sea with a 1,760 t test weight – corresponding to 110% of the nominal load capacity. The test loads consisted of two water filled pontoons which were lifted out of the water and turned around.
After the successful test, the client, Handel Maritime S.A. could deliver the heavy load vessel OSA Goliath to its purchaser, the Mexican company Oceanografia. The OSA Goliath is one of the largest heavy load vessels worldwide and is being used for platform reconditioning, pipe laying and to set up offshore wind power plants.
With its new MTC 78000 Liebherr heavy lift offshore crane, the OSA Goliath is scheduled for working in the Gulf of Mexico on behalf of the Mexican oil company Pemex over the next several years.
Two further Liebherr offshore cranes type CBO 3600-100 are also part of the order. These two cranes will be used as auxiliary cranes as well as for supply hoists.
Unique performance characteristics
The MTC 78000 achieves a maximum lifting capacity of 1,600 t at up to 35 m radius. This corresponds to a maximum dynamic moment of 78,000 mt, the crane still being able to slew over 360°. At a maximum radius of 74 m for the main hoist the crane achieves a lifting capacity of almost 530 t. The boom length of the crane currently delivered is 87 m. In addition to the main hoist, the MTC 78000 offers two auxiliary hoists with lifting capacities of up to 500 t and 50 t respectively.
The dead weight of the new heavy-lift offshore crane is 1,420 t without the base column which weighs approximately another 300 t - depending on its design.
The size of the MTC 78000, which is derived from customer requirements, represents a new dimension in product development for Liebherr. Thereby, the crane’s design is character-ized by state-of-the-art drive technology. The drive concept is based on an electro-hydraulic drive with 8 x 500 kW or 4 MW power. The two main winches offer a line pull of 500 kN (50 t) with a rope diameter of 48 mm.
High safety standards are among the most important criteria to be fulfilled during the development of the new offshore crane. The standard equipment of the MTC 78000 features the proven Litronic control system with integrated display of load and radius as well as automatic load moment limitation. This is completed by special overload protections which are either activated electronically (AOPS “automatic overload protection system”) or manually (MOPS “manual overload protection system”). The crane's auxiliary hoist is fitted with a constant tension system exerting a tensile force on the hoist rope in case of significant wave height, thus ensuring that the hook follows the moving load.
Liebherr: Heavy-Lift Offshore Crane
Liebherr delivers the first MTC 78000 heavy lift offshore crane
At the end of June, Liebherr delivered the first heavy lift offshore crane type MTC 78000 straight from its manufacturing plant in Rostock. The MTC 78000 is one of the biggest offshore slewing cranes worldwide. With a maximum dynamic torque of 78,000 mT, the MTC 78000 is the most powerful machine within the extensive range of cranes and material handling machines offered by the Liebherr group of companies. Four units of the new heavy-lift crane have already been ordered to date.
Despite its size, the MTC 78000 has been designed as a slewing crane and is supported by traditional large-diameter antifriction bearings. With a weight of 70 tons, the swing ring has a diameter of approximately 9 m. The manufacturing of such large mechanical parts can only be accomplished through complicated custom processes as conventional gear cutting machines are only available for large-diameter anti-friction bearings up to a diameter of 5 m. Therefore, Liebherr has acquired correspondingly sized machines and equipment specifically for the mechanical machining of these flanges.
Spectacular heavy lifting
The onsite erection and assembly of the large size crane on the heavy load vessel OSA Goliath presented Liebherr engineers with special challenges – for example, the planning of the individual hoists so that the maximum permitted ground pressure of the pier was not exceeded. As the assembly starting date depended on the arrival of the heavy load vessel and the required lifting equipment needed to be ready on short notice, Liebherr exclusively used their own cranes for the assembly. Two large LHM 600 mobile harbour cranes were used in tandem operation for the heavy duty lifts. Both cranes with their maximum load capacity of 208 tons each enabled parts weighing up to 400 tons to be mounted in tandem operation. The machines were equipped with the recently patented innovative Liebherr “sycratronic” control system. This Dynamic Anti Collision System controls the simultaneous operation of the mobile harbour cranes, so ensuring best possible performance and protection for the cranes.
The assembly of the MTC 78000 required several spectacular heavy duty lifts. First, the slewing platform was mounted – at 370 t, the heaviest of the components. Thereafter, the machinery compartment with the drive components (approximately 240 t), the mast lower section (about 250 t) and the mast upper section (around 160 t) of which the lowest point needed to be hoisted up to over 43 m above the pier level. This hoisting height was made possible by equipping the mobile harbour cranes with two corresponding tower extensions.
The last step in the assembly process involved putting the boom in place. In a tandem hoist operation, the 87 m boom was positioned with millimeter precision at the respective connection points enabling the boom to be pinned to the slewing platform on both sides. The sheer size of the pins required a specially developed hydraulic pinning machine.
Due to precise project planning, the specially trained team of 50 mechanics was able to assemble the MTC 78000 in only 23 days.
Overload test offshore
The heavy lifting test of the large crane was carried out in the open sea with a 1,760 t test weight – corresponding to 110% of the nominal load capacity. The test loads consisted of two water filled pontoons which were lifted out of the water and turned around.
After the successful test, the client, Handel Maritime S.A. could deliver the heavy load vessel OSA Goliath to its purchaser, the Mexican company Oceanografia. The OSA Goliath is one of the largest heavy load vessels worldwide and is being used for platform reconditioning, pipe laying and to set up offshore wind power plants.
With its new MTC 78000 Liebherr heavy lift offshore crane, the OSA Goliath is scheduled for working in the Gulf of Mexico on behalf of the Mexican oil company Pemex over the next several years.
Two further Liebherr offshore cranes type CBO 3600-100 are also part of the order. These two cranes will be used as auxiliary cranes as well as for supply hoists.
Unique performance characteristics
The MTC 78000 achieves a maximum lifting capacity of 1,600 t at up to 35 m radius. This corresponds to a maximum dynamic moment of 78,000 mt, the crane still being able to slew over 360°. At a maximum radius of 74 m for the main hoist the crane achieves a lifting capacity of almost 530 t. The boom length of the crane currently delivered is 87 m. In addition to the main hoist, the MTC 78000 offers two auxiliary hoists with lifting capacities of up to 500 t and 50 t respectively.
The dead weight of the new heavy-lift offshore crane is 1,420 t without the base column which weighs approximately another 300 t - depending on its design.
The size of the MTC 78000, which is derived from customer requirements, represents a new dimension in product development for Liebherr. Thereby, the crane’s design is character-ized by state-of-the-art drive technology. The drive concept is based on an electro-hydraulic drive with 8 x 500 kW or 4 MW power. The two main winches offer a line pull of 500 kN (50 t) with a rope diameter of 48 mm.
High safety standards are among the most important criteria to be fulfilled during the development of the new offshore crane. The standard equipment of the MTC 78000 features the proven Litronic control system with integrated display of load and radius as well as automatic load moment limitation. This is completed by special overload protections which are either activated electronically (AOPS “automatic overload protection system”) or manually (MOPS “manual overload protection system”). The crane's auxiliary hoist is fitted with a constant tension system exerting a tensile force on the hoist rope in case of significant wave height, thus ensuring that the hook follows the moving load.
For more information, please visit:
https://edir.bulk-online.com/profile...rk-nenzing.htm10109 liebherr werk nenzing.htm
http://www.google.com/search?hl=de&c...btnG=Suche&lr=search?hl=de&client=safari&rls=de de&q=Liebherr+site%3Abulk online.com&btnG=Suche&lr=
Additional information:
http://www.google.com/search?hl=de&c...btnG=Suche&lr=search?hl=de&client=safari&rls=de de&q=Offshore+Cranes+++site%3Abulk online.com&btnG=Suche&lr=
Fig. 1: Assembly mast upper section
Fig. 2: Assembly of boom with vessel
Fig. 3: Overload test with 1.760 t test weight
Attachments
1_liebherr_mtc-78000 (JPG)
2_liebherr_mtc-78000 (JPG)
3_liebherr_mtc-78000 (JPG)
liebherr_logo (JPG)
■